Terex Genie Z-40 Скачать руководство пользователя

Страница: 48 / 287

Service and Repair Manual

June 2022

Primary Boom Components

-62/40

Part No. 1268555GT

Primary Boom Components

4-1 C able Tra ck

4-1

Cable Track

The primary boom cable track guides the cables

and hoses running up the boom. It can be repaired

link by link without removing the cables and hoses

that run through it. Removing the entire primary

boom cable track is only necessary when

performing major repairs that involve removing the

primary boom.

How to Re mov e th e Cabl e T rack

How to Remove the Cable Track

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Disconnect the wire connectors from the

bottom of the platform control box.

Note: When installing the wire connectors to the

bottom of the platform control box, match the color

of the connectors to those on the control box to be

sure they are installed in the correct location.
2 Disconnect the power to plat cable from the

AC outlet box.

3 Remove the hose and cable clamps from the

platform support.

4 Tag, disconnect and plug the platform leveling

slave cylinder hydraulic hoses from the

bulkhead fittings on the top of the primary

boom. Cap the bulkhead fittings.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

5 Tag, disconnect and plug ports V1 and V2 on

the platform rotate/jib manifold. Cap the

fittings.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

6 Remove the hose and cable cover from the

side of the jib boom.

7 Remove the retaining fasteners securing the

cable track to the upper tube.

8 Pull the cable track back from the upper tube.
9 Remove the hose and cable clamps from

inside the cable track at both ends.

10 Pull the hoses and cables out of the upper

tube.

11 Pull the hoses and cables out of the cable

track.

12 Remove the retaining fasteners that attach

the cable track to the lower tube.

13 Remove the cable track from the machine.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды