Terex Genie Z-40 Скачать руководство пользователя

Страница: 96 / 287

Service and Repair Manual

June 2022

Axle Components

-62/40

Part No. 1268555GT

Axle C ompone nts

10-1 Oscillatin g Axle Cylin ders

10-1

Oscillating Axle Cylinders

The oscillating axle cylinders extend and retract

between the drive chassis and the oscillating axle.

The cylinders are equipped with counterbalance

valves to prevent movement in the event of a

hydraulic line failure. The valves are not

adjustable.

How to Remove an Oscillating

Axle Cylinder

Note: Perform this procedure with the machine on

a firm, level surface with the boom in the stowed

position.
Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Rotate the turntable until the boom is between

the steer tires or tracks.

2 Tag, disconnect and plug the oscillating axle

cylinder hydraulic hoses. Cap the fittings on

the oscillate cylinder.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

3 Remove the pin retaining fasteners from the

rod-end pivot pin. Use a soft metal drift to

remove the pin.

4 Attach a lifting strap from an overhead lifting

device to the barrel end of the oscillating

cylinder.

5 Remove the pin retaining fasteners from the

barrel-end pivot pin. Use a soft metal drift to

remove the pin.

6 Remove the oscillate cylinder from the

machine.

Crushing hazard. The oscillate

cylinder may become

unbalanced and fall when

removed from the machine if not

properly attached to the lifting

device.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды