Terex Genie Z-40 Скачать руководство пользователя

Страница: 63 / 287

June 2022

Service and Repair Manual

Engines

Part No. 1268555GT

-62/40

6-7 Die sel Par ticle Filter R ege ner ation - De utz TD 2. 2 L3

6-7

Diesel Particle Filter

Regeneration - Deutz TD 2.2 L3

Engine

The combustion of diesel fuel results in soot,

which is separated in the diesel particle filter

(DPF). This must be regenerated as the

contamination with soot increases. There are

3 types of regeneration.

Passive regeneration:

Under normal operating conditions when the

exhaust temperature is >482°F / 250°C the particle

filter contamination with soot remains in a

permissible range. This process is automatically

activated by the engine control unit, the operator

does not need to perform any actions.

Standstill regeneration:

If passive regeneration does not attain an

adequate reduction of the soot contamination, the

particle filter will continue to become contaminated

with soot and a standstill regeneration will be

required by the operator.
To perform standstill regeneration, refer to the

Operator's Manual on your machine.

Service regeneration:

If a fault occurs, the system reacts by reducing the

engine performance. This can include limited

machine functions, torque reduction, reduced

engine rpm and replacement of the DPF.
If standstill regeneration is prohibited by the

operator. Service regeneration must be performed

by a trained technician with the use of the DEUTZ

SerDia software tool and DeCom interface cable.

Available from Deutz.
If service regeneration is not performed,

replacement of the DPF will be required.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды