Terex Genie Z-40 Скачать руководство пользователя

Страница: 57 / 287

June 2022

Service and Repair Manual

Engines

Part No. 1268555GT

-62/40

Engi nes

6-1 RPM adju stme nt - Deut z Mo dels

6-1

RPM Adjustment -

Deutz Models

Refer to Maintenance Procedure in the appropriate

Service or Maintenance Manual for your machine,

Check and Adjust the Engine RPM

6-2 RPM adju stme nt - Perkin s M odels

6-2

RPM Adjustment -

Perkins Models

Refer to Maintenance Procedure in the appropriate

Service or Maintenance Manual for your machine,

Check and Adjust the Engine RPM

6-3 Flex Plat e

6-3

Flex Plate

The flex plate acts as a coupler between the

engine and the pump. It is bolted to the engine

flywheel and has a splined center to drive the

pump.

How to Remove the Flex Plate

Deutz models:

1 Remove the tailpipe bracket mounting

fasteners from the engine bell housing.

2 Support the drive pump assembly with an

appropriate lifting device.

3 Remove all of the engine bell housing

fasteners.

4 Carefully pull the pump and bell housing

assembly away from the engine and secure it

from moving.

Component damage hazard.

Hoses can be damaged if they

are kinked or pinched.

5 Remove the flex plate mounting fasteners.

Remove the flex plate from the flywheel.

Ford models:

1 Disconnect the electrical connectors from

both oxygen sensors at the tailpipe and

exhaust manifold. Do not remove the oxygen

sensors.

2 Remove the exhaust pipe fasteners at the

muffler.

3 Support the muffler and bracket assembly

with a suitable lifting device.

4 Remove the muffler bracket mounting

fasteners from the bell housing. Carefully

remove the muffler and bracket assembly

from the engine.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды