Terex Genie Z-40 Скачать руководство пользователя страница 92

Страница: 92 / 287

Service and Repair Manual

June 2022

Manifolds

-62/40

Part No. 1268555GT

8-16 V alve Coils

8-16

Valve Coils

How to Test a Coil

A properly functioning coil provides an

electromotive force which operates the solenoid

valve. Critical to normal operation is continuity

within the coil that provides this force field.
Since coil resistance is sensitive to temperature,

resistance values outside specification can

produce erratic operation. When coil resistance

decreases below specification, amperage

increases. As resistance rises above specification,

voltage increases.
While valves may operate when coil resistance is

outside specification, maintaining coils within

specification will help ensure proper valve function

over a wide range of operating temperatures.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

1 Tag and disconnect the wiring from the coil to

be tested.

2 Test the coil resistance.

Result: The resistance should be within

specification, plus or minus 30%.

Result: If the resistance is not within

specification, plus or minus 30%, replace the

coil.

Valve Coil Resistance

Specification

Note: The following coil resistance specifications

are at an ambient temperature of 68°F / 20°C. As

valve coil resistance is sensitive to changes in air

temperature, the coil resistance will typically

increase or decrease by 4% for each 18°F / 10°C

that your air temperature increases or decreases

from 68°F / 20°C.

Valve Coil Resistance Specification

Solenoid valve, 3 position 4 way, 10V DC

5 to 7

Ω

(schematic items D, V and Y)

Solenoid valve, 3 position 4 way, 10V DC

4 to 6

Ω

(schematic item BB)

Solenoid Valve, 2 position 3 way, 10V DC

5 to 7

Ω

(schematic items B, C, E, F and FF)

Solenoid Valve, 2 position 3 way, 10V DC

5.5 to 7.5

Ω

schematic items( KK and LL)

Proportional solenoid valve, 12V DC

4 to 6

Ω

schematic items( M and T)

Proportional solenoid valve, 12V DC

3.7 to 5.7

Ω

(schematic item Q)

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Бренды по названию

Популярные бренды