Appendix A: Errors
Vision G2 Testers User Guide—74-108-800 Rev. H—12 June 2019
139 of 158
Vision Tester Errors
Error
Code
Error
Category Title
Message
Fault
Check the Following
1000
4
AutoMag Error
AutoMag misaligned or jammed. Check
for obstructions.
The tester detected the AutoMag did not move, or did not
move as expected at the event.
1. AutoMag misaligned or jammed
2. AutoMag motor connection
3. AutoMag motor failure
4. Main board failure
1001
4
AutoMag Error
AutoMag not homed. Home the
AutoMag.
The AutoMag was not homed properly. Home the
AutoMag before running the test.
1. AutoMag misaligned or jammed
2. AutoMag motor connection
3. AutoMag motor failure
4. Main board failure
1002
4
AutoMag Homing Error
AutoMag is unable to home against
drive plate. Contact Tech Support.
AutoMag did not detect upper home position.
1. AutoMag is able to home against drive plate
2. The AutoMag motor failure
1003
4
AutoMag Comm Error
Cannot communicate with AutoMag or
wrong probe configuration. Check
system configuration.
1004
6
DTP X Missing
1005
6
DTP Configuration Error
1006
6
DTP Communication Error
The tester is unable to communicate with <probe
number>.
1. Digital Temperature Probe cable connection
2. Digital Temperature probes configuration
3. Digital Temperature Probes connection to AutoMag board
4. Digital temperature probes failure
5. Main board failure
1007
1
DTP Configuration Mismatch
DTP configuration and protocol do not
match.
The protocol is trying to use DTPs that are not configured.
Enable DTPs in configuration.
1. The vessel temperature field for protocol
2. System configuration of Digital Temperature Probes
1008
1
Probe Offset Out of Range
Desired offset is outside the range of ‐
9.99 through 9.99. Check offset. If the
problem persists, contact Tech Support.
User tried to apply an offset greater than 9.99 or less than ‐
9.99.
1. Probe offset is entered correctly
2. Temperature probe failure
1009
4
External Probe Error
Cannot communicate with the external
temperature probe. Make sure the
probe is connected.
The tester can't communciate with the external
temperature probe.
1. External temperature probe connection
2. External temperature probe failure
3. Main board failure
1010
6
External Probe Comm. Error
The tester can't communciate with the external
temperature probe.
1011
6
External Probe Bad Temp Read
Temperature value read was outside expected range
1012
6
Auxiliary CPU Error
Either second CPU is not programmed with firmware or
has the wrong firmware or there is temporary or
permanent board failure that causes communication
problems between the two CPUs on the main board. The
error could only be reported during diagnostics.
Main board failure
1013
6
Speed Tolerance Error
During diagnostics the paddle speed was outside 4%
tolerance of 50 rpm.
1. Check the motor
2. Check the belt
3. Check the main board
1014
1
Set Sampling to Manual
Collect or Collect and Detect protocols
must be run on the AutoPlus. Set
Sampling to Manual.
User has tried to run a protocol with automation on a
tester.
Sampling Mode field for protocol.
1015
6
DTP X Unknown Calibration
1016
6
External Probe Unknown Calibration
Содержание VISION G2 CLASSIC 6
