Teledyne 2120XL Скачать руководство пользователя страница 61

Страница: 61 / 85

Trace Nitrogen in Argon Analyzer

Operation

Teledyne Analytical Instruments

If instrument is turned off, the next time the instrument is powered,

the instrument will automatically perform a calibration cycle after 3
minutes of entering the sample mode if

AUTO CAL

functions were on

prior to shut down.

4.5.1.7

LOW

This function allows the user to set the flowrate through the flow

control valve. The first line of the display indicates the current flow
setting in ccm and can be manipulated using the

▲

▼

arrow keys. The

second line of the display is a read-only item that displays the live
sensor voltage within the flow control module.

To set or change the flow rate, press the

SYSTEM

key and use the

◄►

arrow keys to position the blinking over the

function, and

press ENTER. A second screen of system function will appear. Use the

◄►

arrow keys to position the blinking over the

Flow

function, and

press ENTER to enter the function. The following screen will appear:

Flow: 100.0 ccm

Sens Vout: 300.0 mV

The current flow rate (100) will be blinking and can be changed

using the

▲

▼

arrow keys. Press ENTER when the proper flow rate is

indicated on the display screen.

4.5.1.8

RACKING

URING

ALIBRATION

The user has the option of setting the preference as to whether the

analog outputs track the display readings during calibration or not. The
function can be toggled between Track or Hold in this function.

To set the preference, press the

SYSTEM

key and the first System

menu will appear in the VFD display. Use the

◄►

arrow keys to

position the blinking over the

function, and press ENTER. A

second screen of system function will appear. Use the

◄►

arrow keys to

position the blinking over the

Track (

Hold)

function, and toggle

between Track or Hold using the

▲

▼

arrow keys. Press ENTER when

the desired selection is indicated on the display screen.

If Hold is selected, the next function

Calholdtimer

sets the hold

period.

Содержание 2120XL






















































































Результаты поиска

Содержание 2120XL

Отзывы:

Teledyne 2120XL, Руководство по эксплуатации, Страница: 61 / 85

Результаты поиска

Содержание 2120XL

Отзывы: