manualshive.com logo in svg

Teledyne 2120XL, Руководство по эксплуатации, Страница: 43 / 85

Поделиться
Скачать
Teledyne 2120XL Скачать руководство пользователя страница 43

Trace Nitrogen in Argon Analyzer  

Installation 

 

 

 

Teledyne Analytical Instruments 

31 

3.6.2 Gas Connections to the Instrument 

CAUTION: 

EQUIPMENT DAMAGE MAY RESULT IF THE 
ANALYTICAL CELL IN THIS UNIT IS EXPOSED TO 
PRESSURE ABOVE ATMOSPHERIC, CAUSING IT TO 
BREAK OR SHATTER. TO PREVENT THIS, NEVER 
EXCEED 20 PSIG (138 KPA) ON THE INLET PORT. 
ALWAYS ENSURE THAT THE VENT IS AT 
ATMOSPHERIC PRESSURE. 
 
DO NOT REMOVE THE FLOW CONTROL ORIFICE 
FROM THE SAMPLE INLET OF THE ANALYZER.  
 
DO NOT BLOCK THE VENT. 

  To connect the gas line: 

1.

 

Connect an unobstructed vent line to the 1/8-in Swagelok 
fitting on the vent port on the rear of the analyzer. 

2.

 

Connect the inlet line from the sample manifold system, 
regulated to 4 to 20 psig (41 kPa), to the 1/8-in Input port 
fitting on the rear of the analyzer. 

3.7 Purging 

The Model 2120XL is equipped with a flow control module 

installed in the analyzer sample inlet to regulate flow and pressure to the 
analytical cell. A maximum inlet pressure of 20 psig (138 kPa) is 
allowable. 

CAUTION: 

OZONE EMISSIONS ARE POSSIBLE IF AIR OR 
MOISTURE IS IONIZED IN THE SAMPLING SYSTEM. 
THE SAMPLE PATH MUST BE RELATIVELY FREE 
OF AIR AND/OR MOISTURE BEFORE APPLYING THE 
IONIZING VOLTAGE.  
 
KEEP THE MODEL 2120XL POWER OFF AND PURGE 
THE EXTERNAL TUBING. THEN APPLY POWER  TO 
PURGE THE INTERNAL LINES. ANALYZER POWER 
IS NEEDED TO PURGE ANALYZER SINCE THE 
FLOW CONTROL MODULE NEEDS POWER TO 
OPERATE. 

 

 

Содержание 2120XL






















































































Отзывы:

Нет отзывов