Teledyne 2120XL Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 85

Teledyne 2120XL Скачать руководство пользователя страница 34

Installation Model

2120XL

Teledyne Analytical Instruments

22

Alarm Relays:

The nine alarm-circuit connector pins connect to the

internal alarm relay contacts. Each set of three pins provides one set of
Form C relay contacts. Each relay has both normally open and normally
closed contact connections. The contact connections are shown in Table
3-2. They are capable of switching up to 3 amperes at 250 VAC into a
resistive load. The connectors are:



Threshold Alarm 1:



Can be configured as high (actuates when concentration is
above threshold), or low (actuates when concentration is
below threshold).



Can be configured as failsafe or non-failsafe.



Can be configured as latching or non-latching.



Can be configured out (defeated).



Threshold Alarm 2:



Can be configured as high (actuates when concentration is
above threshold), or low (actuates when concentration is
below threshold).



Can be configured as failsafe or non-failsafe.



Can be configured as latching or non-latching.



Can be configured out (defeated).

Table 3-2: Alarm Relay Contact Pins

Pin Contact

45

Threshold Alarm 1, normally closed contact

28

Threshold Alarm 1, moving contact

46

Threshold Alarm 1, normally open contact

42

Threshold Alarm 2, normally closed contact

44

Threshold Alarm 2, moving contact

43

Threshold Alarm 2, normally open contact

36

System Alarm, normally closed contact

20

System Alarm, moving contact

37

System Alarm, normally open contact

«
...
32
33
34
35
36
...
»

Содержание 2120XL






















































































Отзывы:

Нет отзывов