Teledyne 2120XL Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 85

Teledyne 2120XL Скачать руководство пользователя страница 22

Introduction Model

2120XL

Teledyne Analytical Instruments

10

1.7.4 Summary of Known Hazards

This equipment is designed to minimize your exposure to the process

gases and other known hazards. Read and thoroughly understand all
safety aspects of this system and its operation before operating or
maintaining the equipment.

1.7.4.1

E

LECTROCUTION

WARNING:

DO NOT OPERATE THE ANALYZER WITHOUT THE
COVER SECURED IN PLACE. THE OUTPUT OF THE
HIGH-VOLTAGE TRANSFORMER AND THE
ANALYTICAL CELL ELECTRODES CAN APPROACH
VOLTAGES OF 6,000 VAC OR HIGHER. TO GUARD
AGAINST ELECTRICAL SHOCK AND POSSIBLE
ELECTROCUTION, THE ANALYZER SHOULD BE
SERVICED ONLY BY A QUALIFIED SERVICE
TECHNICIAN.

Adherence to the following guidelines helps guard against electrical

shock:



For safety and proper performance, this analyzer must be
connected to a properly grounded three-wire source of
electrical power.



Tampering or unauthorized substitution of components may
adversely affect the safety of this instrument. Use only
factory-approved components for repair.



Before checking or replacing any chassis component, turn off
the power and remove the AC power cord from the rear
panel.

1.7.4.2

P

RESSURE

WARNING:

MISHANDLING OF GAS CYLINDERS COULD
RESULT IN DEATH, SERIOUS INJURY, OR
PROPERTY DAMAGE. HANDLE AND STORE GAS
CYLINDERS WITH EXTREME CARE AND IN
ACCORDANCE WITH MANUFACTURER'S
INSTRUCTIONS.

Sudden or uncontrolled release of pressurized gas can cause serious

injury. The hazards of high pressure can be avoided through careful
inspection and handling of cylinders and equipment with proper

«
...
20
21
22
23
24
...
»

Содержание 2120XL






















































































Отзывы:

Нет отзывов