manualshive.com logo in svg

Teledyne 2120XL, Руководство по эксплуатации, Страница: 13 / 85

Поделиться
Скачать
Teledyne 2120XL Скачать руководство пользователя страница 13

Trace Nitrogen in Argon Analyzer 

Introduction 

 Teledyne 

Analytical 

Instruments 

1

 

 

Introduction 

1.1 Overview 

This manual describes installation, operation and maintenance for 

the Model 2120XL Trace Nitrogen in Argon Gas Analyzer. Section 1 
describes the analyzer in general terms and provides additional safety 
information pertinent to the proper operation of the instrument. 

The Teledyne Model 2120XL Trace Nitrogen in Argon Gas 

Analyzer is a robust analytical tool for measuring trace amounts of 
nitrogen in argon. Using precise optical filtering, single line emission 
characteristic of nitrogen is produced with an intensity proportional to 
the nitrogen concentration.  

The Model 2120XL has three user programmable analysis ranges 

extending from 0-1 ppm to 0-100 ppm with corresponding analog output 
signals that are proportional to the concentration on the selected range. 
The nitrogen concentration is displayed on the front panel and the 
analog output signals are available at the rear panel.   Digital 
communication is achieved with a standard RS-232 serial port. 

The system is easy to operate with all controls and indicators 

accessible from the front panel. Digital flow control, two adjustable 
concentration alarms, system alarm, self-diagnostics are just a few of the 
many features included on the standard Model 2120XL instrument. 

1.2 Typical Applications 

The Model 2120XL Trace Nitrogen in Argon Gas Analyzer is used 

in a wide range of applications including: 

 

Air separation plants 

 

 Argon Purification Plants 

 

Specialty Gas Laboratories 

 

Specialty Steel Manufacturing 

 

Gas Management/Monitoring Systems 

Содержание 2120XL






















































































Отзывы:

Нет отзывов