manualshive.com logo in svg

Teledyne 2120XL, Руководство по эксплуатации, Страница: 54 / 85

Поделиться
Скачать
Teledyne 2120XL Скачать руководство пользователя страница 54

Operation Model 

2120XL 

 

 

Teledyne Analytical Instruments 

42 

 

indicates a problem in a specific area of the instrument. Refer to Chapter 

5 Maintenance and Troubleshooting

 for number-code information. The 

results screen alternates for a time with: 

 

Press Any Key 

To Continue... 

 
Then the analyzer returns to the initial System screen.  

4.5.1.3

 

P

ASSWORD 

P

ROTECTION

 

Security can be established by choosing a 3 digit password (PSWD) 

from the standard ASCII character set. (See Installing or Changing a 
Password, below, for a table of ASCII characters available.) 

Once a unique password is assigned and activated, the operator 

MUST enter the UNIQUE password to gain access to set-up functions 
which alter the instrument's operation, such as setting the instrument 
span or zero setting, adjusting the alarm setpoints, or defining an 
analysis range. 

After a password is assigned, the operator must log out to activate 

it. Until then, anyone can continue to operate the instrument without 
entering the new password. 

Only one password can be defined. Before a unique password is 

assigned, the system assigns TAI by default. This allows access to 
anyone. After a unique password is assigned, to defeat the security, the 
password must be changed back to TAI. 

If a password is assigned, then setting the following instrument 

parameters can be done only after the password is entered: 

span

 and 

zero

 settings, 

alarm

 setpoints, analysis 

range

 definitions, switching 

between 

auto ranging 

and manual override. In addition, all 

System

 

functions such as setting up an 

auto-cal

, 

self-test

 and assigning a new 

password

 etc. with the exception of 

Track/Hold

 and 

Model

 

 

cannot be 

accessed without entering a password.  However, the instrument can still 
be used for analysis without entering the password. 

If you have decided not to employ password security, use the 

default password 

TAI

. This password will be displayed automatically by 

Содержание 2120XL






















































































Отзывы:

Нет отзывов