Teledyne 2120XL Скачать руководство пользователя страница 60

Страница: 60 / 85

Operation Model

2120XL

Teledyne Analytical Instruments

Model 2120XL is accurate to 2-3 %. Accordingly, internally
scheduled calibrations can vary 2-3 % per day.

To setup an Auto Cal cycle:
Choose

SYSTEM

from the function buttons. Use the

◄►

arrow

keys to position the blinking over the

function, and press ENTER.

A second display of

System

functions will appear. Use the

◄►

arrow

keys again to position the blinking over the

Auto Cal

function, and

press ENTER to enter the function. The following screen will appear:

Zero In 0d 0h Off

Span In 0d 0h Off

Press the

▲

▼

arrow keys to blink

ZERO

(or

SPAN

), then press

ENTER

again.

Note: You will be unable to set

OFF

if a zero interval is

entered.

Span Every ...

(or

Zero Every ...

) screen appears.

Zero schedule: OFF

Day: Ød Hour: Øh

Move the blinking highlight to the

Day

field , then use the

▲

▼

arrow keys to display the correct value for the day.

Once the correct day is displayed press ENTER to accept the value

and to move to the start-time value. Use the

▲

▼

arrow keys to set a

start-time value. Press ENTER again to accept the value.

To turn ON the

SPAN

and/or

ZERO

cycles (to activate the auto cal

feature):

If a scheduled day and time has just been entered, press ESCAPE to

return to the previous menu or press

SYSTEM

again and move to the

AUTO CAL

function with the

◄►

keys

and press ENTER

again.

When the

ZERO/SPAN

values screen appears, use the

▲

▼

arrows

to blink the

ZERO

(or

SPAN

) and press ENTER

to go to the next screen.

Use the

◄►

arrows to select the

OFF/ON

field. Use the

▲

▼

arrows to

set the

OFF/ON

field to

. You can now turn these fields ON because

there is a nonzero span interval defined.

Содержание 2120XL






















































































Результаты поиска

Содержание 2120XL

Отзывы:

Teledyne 2120XL, Руководство по эксплуатации, Страница: 60 / 85

Результаты поиска

Содержание 2120XL

Отзывы: