Teledyne 2120XL Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 85

Teledyne 2120XL Скачать руководство пользователя страница 4

Model

2120XL

Teledyne Analytical Instruments

iv

Safety Messages

Your safety and the safety of others is very important. We have

provided many important safety messages in this manual. Please read
these messages carefully.

A safety message alerts you to potential hazards that could hurt you

or others. Each safety message is associated with a safety alert symbol.
These symbols are found in the manual and inside the instrument. The
definition of these symbols is described below:

GENERAL

WARNING/CAUTION

: Refer to the instructions for

details on the specific danger. These cautions warn
of specific procedures which if not followed could
cause bodily Injury and/or damage the instrument.

CAUTION:

H

OT

S

URFACE

W

ARNING

:

This warning is specific to

heated components within the instrument. Failure to
heed the warning could result in serious burns to
skin and underlying tissue.

WARNING:

E

LECTRICAL

S

HOCK

H

AZARD

:

Dangerous voltages appear

within this instrument. This warning is specific to
an electrical hazard existing at or nearby the
component or procedure under discussion. Failure
to heed this warning could result in injury and/or
death from electrocution.

Technician Symbol

:

All operations marked with this symbol are to be

performed by qualified maintenance personnel only.

NOTE:

Additional information and comments regarding a
specific component or procedure are highlighted in
the form of a note.

No

Symbol

«
...
2
3
4
5
6
...
»

Содержание 2120XL






















































































Отзывы:

Нет отзывов