manualshive.com logo in svg

Teledyne 2120XL, Руководство по эксплуатации, Страница: 37 / 85

Поделиться
Скачать
Teledyne 2120XL Скачать руководство пользователя страница 37

Trace Nitrogen in Argon Analyzer  

Installation 

 

 

 

Teledyne Analytical Instruments 

25 

  18 

Range 3 ID Contact 

  34 

Range 4 ID Contact (not used) 

  35 

Range 4 ID Contact (not used) 

 

Network I/O:

 A serial digital input/output for local network protocol. 

At this printing, this port is not yet functional. It is to be used for future 
options to the instrument. Pins 13 (+) and 29 (–). 

Remote Valve Connections:

  The Model 2120XL is a single-chassis 

instrument and does not have a Remote Probe. Instead, the Remote 
Probe connections are used as a method for directly controlling external 
sample/zero/span gas valves.  See Figure 3-4. 

Figure 3-4: Remote Valve Connections 

 
The voltage from these outputs is nominally 0 V for the OFF and 

15 VDC for the ON conditions. The maximum combined current that 
can be pulled from these output lines is 100 mA. (If two lines are ON at 
the same time, each must be limited to 50 mA, etc.) If more current 
and/or a different voltage is required, use a relay, power amplifier, or 
other matching circuitry to provide the actual driving current.  

In addition, each individual line has a series FET with a nominal 

ON resistance of 5 ohms (9 ohms worst case). This can limit the 
obtainable voltage, depending on the load impedance applied. See 
Figure 3-5.      

 

Содержание 2120XL






















































































Отзывы:

Нет отзывов