manualshive.com logo in svg

Teledyne 2120XL, Руководство по эксплуатации, Страница: 3 / 85

Поделиться
Скачать
Teledyne 2120XL Скачать руководство пользователя страница 3

Trace Nitrogen in Argon Analyzer  

 

 

 

 

Teledyne Analytical Instruments 

iii

 

Specific Model Information 

This instrument relies on the known spectrum emitted from a 

plasma discharge from a distinct gas mixture of variable composition at 
or near atmospheric pressure. This instrument cannot be used for 
analysis on any gas or gas mixture other than nitrogen in argon or a 
mixture specified at the time of purchase. Specific filters carefully 
chosen and tested at the factory have been installed for the particular gas 
mixture. Using this instrument to analyze any other gas mixture will 
result in serious error. Consult the factory for additional information for 
gas analysis not specified at the time of purchase.  

 
 

Instrument Serial Number:

 

 _______________________ 

 

 

 

 

Instrument Range:  _______________ 

 

Calibrated for: 

_______________ 

 

Background Gas:  _______________ 

 

Zero Gas:   

 _______________ 

 

Span Gas:   

_______________ 

 

Содержание 2120XL






















































































Отзывы:

Нет отзывов