manualshive.com logo in svg

Teledyne 2120XL, Руководство по эксплуатации, Страница: 11 / 85

Поделиться
Скачать
Teledyne 2120XL Скачать руководство пользователя страница 11

Trace Nitrogen in Argon Analyzer  

 

 

 

 

Teledyne Analytical Instruments 

xi

 

 

 

DANGER 

COMBUSTIBLE GAS USAGE 

WARNING

 

 

 
 

This is a general purpose instrument designed for use in a 
non-hazardous area.  It is the customer's responsibility to 
ensure safety especially when combustible gases are 
present since the potential of gas leaks always exist. 

Never introduce gases other than argon into the analyzer. If 
explosive, flammable or corrosive gases or gas mixtures are 
allowed to flow into the analyzer, fire or explosion can result.  

Sample gas introduced must be at or very close to 
atmospheric pressure or damage to the detector will result. 

To avoid serious injury, read all precautionary labels 
attached to equipment, cylinders, containers, and boxes 
prior to start-up. 

Labels attached in appropriate areas of the analyzer warn 
you of inherent hazards associated with the system. For 
personal safety, read the labels and perform directed 
precautions before handling the equipment. 

The customer should ensure that the principles of operating 
this equipment are well understood by the user.  Misuse of 
this product in any manner, tampering with its components, 
or unauthorized substitution of any component may 
adversely affect the safety of this instrument. 

Since the use of this instrument is beyond the control of 
Teledyne Analytical Instruments, referred as TAI, no 
responsibility by TAI, its affiliates, and agents for damage or 
injury from misuse or neglect of this equipment is implied or 
assumed. 

Содержание 2120XL






















































































Отзывы:

Нет отзывов