Teeter FreeStep LT1, Инструкции по сборке и использованию, Страница: 9 / 24

7
REVISIONS
ENGR DATE REV SHT ZONE DESCRIPTION
NMS 10/18/2017 A 1 8D A1: RELEASE FOR PATENT
PARTS LIST
ITEM QTY NET DIMENSIONS/DESCRIPTION NOTE MATERIAL SHT
REVISION STATUS
SHT 1
REV A
8
A
1 2 3 4 5 6 7
D
C
B
C
A
D
B
5 3 1 6 2 4 8 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
= .1
= .03
= .005
= 1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
8
A
1 2 3 4 5 6 7
D
C
B
C
A
D
B
5 3 1 6 2 4 8 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
= .1
= .03
= .005
= 1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
REVISIONS
ENGR DATE REV SHT ZONE DESCRIPTION
NMS 10/18/2017 A 1 8D A1: RELEASE FOR PATENT
PARTS LIST
ITEM QTY NET DIMENSIONS/DESCRIPTION NOTE MATERIAL SHT
REVISION STATUS
SHT 1
REV A
8
A
1 2 3 4 5 6 7
D
C
B
C
A
D
B
5 3 1 6 2 4 8 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
= .1
= .03
= .005
= 1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
8
A
1 2 3 4 5 6 7
D
C
B
C
A
D
B
5 3 1 6 2 4 8 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
= .1
= .03
= .005
= 1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
Washer
115
Phillips Head Screw
118
Figure 7:
Locate the Pedals, noting Right
and Left markings. Align each Pedal to the
corresponding Base Pedal Arm.
Figure 8: Use the Step 2 Hardware Kit to attach
the Pedals. Hand tighten 12 × Phillips Head
Screws with 12 × Washers as shown.
Proceed to fully tighten all the Phillips Head
Screws with the Phillips Head Screwdriver.
Once the Pedals are installed, return the
FreeStep to the upright position by lowering
the Front Crossbar and rotating on the Rear
Stabilizer.
Figure 7
Figure 8
Step 2 Hardware