Teeter FreeStep LT1, Инструкции по сборке и использованию, Страница: 10 / 24

8
REVISIONS
ENGR DATE REV SHT ZONE DESCRIPTION
NMS 10/18/2017 A 1 8D A1: RELEASE FOR PATENT
PARTS LIST
ITEM QTY NET DIMENSIONS/DESCRIPTION NOTE MATERIAL SHT
REVISION STATUS
SHT 1
REV A
8
A
1 2 3 4 5 6 7
D
C
B
C
A
D
B
5 3 1 6 2 4 8 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
= .1
= .03
= .005
= 1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
8
A
1 2 3 4 5 6 7
D
C
B
C
A
D
B
5 3 1 6 2 4 8 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
= .1
= .03
= .005
= 1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
Forward Position Holes
Back Position Holes
Seat Installation - Model LT3 only
Skip this step for Model LT1.
Figure 9: The Model LT3 has two Lower Seat assembly
options. Before installing the seat, use this figure to
determine the Position Holes that will be used during
installation. The Forward Position provides the largest
surface area of support during use. The seat can be
adjusted after assembly if needed.
108
9
8
Bolt
Spring Washer
Washer
108
9
8
Bolt
Spring Washer
Washer
Forward Position (side view) Back Position (side view)
MODEL LT3 ONLY : Seat Position Options
FIGURE 4
STEP 3
ASSEMBLE SEAT
Locate the Lower Seat and place it upside-down on
a flat surface, such as the edge of a table. Locate the
Seat Back Assembly and line it up with the Lower Seat.
Figure 10: Use the Step 3a Hardware Kit to assemble
the seat parts. Hand tighten 4 × Bolts with 4 × Spring
Washers and 4 × Washers as shown. Proceed to fully
tighten the Bolts with the Allen Wrench.
Figure 12
Figure 11
Figure 10
Figure 9
Step 3b Hardware
Step 3a Hardware
Figure 12: Use the Step 3b Hardware Kit to attach the
Seat. Hand tighten 4 × Bolts with 4 × Spring Washers
and 4 × Washers as shown. Proceed to fully tighten the
Bolts with the Allen Wrench.
Figure 11:
Before attaching the assembled Seat to the
Seat Post, make sure the Seat Post is fully raised for
better access, then line the Seat up with the Seat Post.
All Models