manualshive.com logo in svg

Tandberg Data MSERIES FC USER, Руководство пользователя, Страница: 19 / 26

Поделиться
Скачать
Tandberg Data MSERIES FC USER Скачать руководство пользователя страница 19

Tandberg Data FC420 Bridge Option User’s Guide

Document T6423053-01, Ver. 1, Rel. 0

November 2002

FC420 Services Software Commands

19

IPAddress

Sets/displays the current IP address of 

the Fibre bridge. If the 

ipdhcp

 

command is enabled, the 

get

 

command reports the current IP 

address assigned by the nameserver.

10.0.0.1

set ipaddress 

xxx.xxx.xxx.xxx

get ipaddress

IPDHCP

Enables/disables the capability of the 

Fibre bridge to request an IP address 

from a DHCP server on the network.

disabled

set ipdhcp [enabled | 

disabled]
get ipdhcp

IPGateway

Sets/displays the current default 

gateway. If the 

ipdhcp

 command is 

enabled, the 

get

 command reports the 

current IP gateway assigned by the 

nameserver.

0.0.0.0

set ipgateway 

xxx.xxx.xxx.xxx

get ipgateway

IPSubnetMask

Sets/displays the current subnet mask. 

If the 

ipdhcp

 command is enabled, the 

get

 command reports the current IP 

subnet mask assigned by the 

nameserver.

255.255.

255.0

set ipsubnetmask 

xxx.xxx.xxx.xxx

get ipsubnetmask

IsReserved (Immediate)

Displays the reservation status of the 

current Fibre bridge services session/

interface. When a reserve flag is set, 

the configuration image4 is 

undergoing modification by another 

Fibre bridge services session. 

Set

 

commands are unavailable while in 

this state. 

Get

 commands are available, 

however.
Executing a 

saveconfiguration

, 

restoreconfiguration

, or 

firmwarerestart

 command releases the 

reserved state so that other users may 

issue set commands.

isreserved

Command

Description

Default

Syntax

Содержание MSERIES FC USER



























Отзывы:

Нет отзывов