manualshive.com logo in svg

Tandberg Data MSERIES FC USER, Руководство пользователя, Страница: 17 / 26

Поделиться
Скачать
Tandberg Data MSERIES FC USER Скачать руководство пользователя страница 17

Tandberg Data FC420 Bridge Option User’s Guide

Document T6423053-01, Ver. 1, Rel. 0

November 2002

FC420 Services Software Commands

17

FcFairArb

Turns on or off the FC-AL arbitration 

fairness. Applies to all three Fibre 

Channel ports on each board.

enabled

set fcfairarb [enabled | 

disabled]
get fcfairarb 

FcFullDuplex

Enables/disables full duplex 

communication between the Fibre 

bridge and other Fibre Channel 

devices.

enabled

set fcfullduplex [enabled | 

disabled]
get fcfullduplex

FcHard

Enables/disables Fibre Channel hard 

address assignment. Under soft 

addressing the FC420 loop address is 

assigned during loop initialization. 

disabled

set fchard [enabled | 

disabled]
get fchard

FcHardAddress

Sets/displays the value used as the FC-

AL hard address.

FC port 0 

0x03

set fchardaddress [

fp

 [

address

]]

get fchardaddress [

fp

]

FcInitiator

Enables/disables the initiator function 

of the Fibre bridge on the Fibre 

Channel network.

disabled

set fcinitiator [enabled | 

disabled]
get fcinitiator

FcPortList

(Immediate)

Lists the available Fibre Channel ports 

and their current status. 

fcportlist

Fcp2

Enables/disables the Fibre bridge’s 

compliance with the FCP-2 Fibre 

Channel specification.

disabled

set fcp2 [enabled | disabled]
get fcp2

Fcp2Conf

Enables/disables the Fibre bridge’s 

capability to request FCP_CONF IUs. 

This option is only valid when the 

fcp2

 

command is also enabled.

disabled

set fcp2crn [enabled | 

disabled]
get fcp2crn

Fcp2CRN

Enables/disables the Fibre bridge’s 

capability to accept CRNs for precise 

delivery of SCSI commands. This 

option is only valid when the 

fcp2

 

command is also enabled.

disabled

set fcp2conf [enabled | 

disabled]
get fcp2conf

FcSCSIBusyStatus

Specify the SCSI status value returned 

when the FC420 is unable to accept a 

SCSI command due to a temporary 

lack of internal resources. 

BUSY

set fcscsibusystatus [busy | 

qfull]
get fcscsibusystatus

FcTargets (Immediate)

Provides the node name, Fibre LUN, 

and inquiry data for every Fibre 

Channel target device visible to a Fibre 

bridge operating in initiator mode.

fctargets <

fp

>

Command

Description

Default

Syntax

Содержание MSERIES FC USER



























Отзывы:

Нет отзывов