manualshive.com logo in svg

Tandberg Data MSERIES FC USER, Руководство пользователя, Страница: 1 / 26

Поделиться
Скачать
Tandberg Data MSERIES FC USER Скачать руководство пользователя страница 1

Document T6423053-01, Ver. 1, Rel. 0, November 2002

1

Tandberg Data FC420
Bridge Option User’s Guide

Introduction

3

Fibre Channel Overview ...................................................................... 3

Library Operation After FC420 Bridge Installation ............................... 3

Cabling the M2500 Library for Fibre Channel

4

One- and Two-Drive Library Cabling ................................................... 4

Cabling with Three or More Drives ...................................................... 5

Setting SCSI IDs

7

Configuring FC420 Firmware

8

Setting Up an Ethernet Connection ..................................................... 8

Verifying Current FC420 Firmware .................................................... 10

Setting Local Echo Mode................................................................... 10

Scanning the SCSI buses on the Library........................................... 10

Creating a Map File for the FC420 .................................................... 11

Making Other Configuration Changes ............................................... 11

Updating FC420 Firmware

12

Содержание MSERIES FC USER



























Отзывы:

Нет отзывов