Takeuchi TB210R Скачать руководство пользователя страница 98

Страница: 98 / 205

3-28

OPERATION

HANDLING RUBBER
CRAWLERS

Rubber crawlers have an inherent weakness,

lack of strength, due to their use of rubber.

Be sure to observe the prohibitions and

cautions below to prevent the crawlers from

being damaged or coming off.

PROHIBITIONS

Do not travel or operate the machine in the

following places:

HANDLING RUBBER CRAWLERS

• Traveling and slewing on crushed rock,

extremely rough hard rock, steel beams,

scrap iron, or near the edges of steel plates

will cause damage to the rubber crawlers.

• Traveling on riverbeds or places where

there are large numbers of boulders may

cause the stones to get caught and

damage the crawler or make the crawler

come off.

• Do not use the machine on the seashore.

The salt may corrode the steel core.

• Do not let fuel, oil, salt or chemical solvents

get on the crawlers. These substances

may corrode the bonding of the steel cores

on the crawlers, resulting in rust or peeling.

If any of these substances gets on the

crawler, immediately clean it off with water.

• It will cause an irregular wear or damage to

the lugs, if the machine travels on irregular

surfaces such as recently paved with

asphalt, exposed to a bonfire or of hot iron

sheets under the blazing sun.

• Do not move earth in places where the

rubber crawlers may slip. Doing so may

speed up lug wear.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды