Takeuchi TB210R Скачать руководство пользователя страница 30

Страница: 30 / 205

1-20

SAFETY

PRECAUTIONS WHEN OPERATING

Cautions when towing

When towing, serious injury or death could

result, if performed incorrectly or the wire

rope being used is inappropriate or not

properly inspected.

• It becomes dangerous if the wire rope

breaks or becomes disengaged. Use a

wire rope appropriate for the required

tractive force.

• Do not use a wire rope that is kinked,

twisted or otherwise damaged.

• Do not apply heavy loads abruptly to the

wire rope.

• Wear safety gloves when handling the wire

rope.

• Make sure there is an operator on the

machine being towed as well as on the

machine that is towing.

• Never tow on slopes.

• Do not let anyone come near to the wire

rope while towing.

Refer to “Towing” for further instructions.

Be careful with flying objects

This machine is not equipped with protective

equipment to protect the operator from flying

objects. Do not use this machine in places

where there are risks of the operator being

hit by flying objects.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды