Takeuchi TB210R Скачать руководство пользователя страница 162

Страница: 162 / 205

6-4

TROUBLESHOOTING

IF THE BATTERY GOES DEAD

The symptoms below indicate that the

battery is dead.

• The starter motor does not turn or fails to

start the engine.

• The horn is too weak.

Remedy procedure

Start the engine using the booster battery on

the other vehicle (booster vehicle) and the

jumper cables.

• When starting the engine using the

jumper cables, be sure to connect the

cables by following the proper steps.

Improper use of jumper cables can

result in battery explosion or

unexpected machine motion.

· Do not allow the booster vehicle and

the machine with a dead battery (dead

machine) to touch each other.

· Do not allow the positive (+) and the

negative (–) clips of the jumper cables

to touch each other.

· When connecting, attach the jumper

cable to the positive (+) terminals first.

When disconnecting, remove the

cable from the negative (–) terminal

(ground) first.

· Connect the last clip of the jumper

cable to a point as far away from the

battery as possible.

• Always wear the protective goggle when

jump starting the engine by using the

jumper cables.

IMPORTANT: Use the jumper cables and

clips of a size suited to the capacity of

battery. Do not use damaged or corroded

jumper cables and clips.

IMPORTANT: Be sure that the battery of

the booster vehicle has the same

capacity as the battery of the dead

machine.

IMPORTANT: Be sure to connect the clips

securely.

IF THE BATTERY GOES DEAD

Connecting the jumper cables

IMPORTANT: Set the starter keys of the

booster vehicle and the dead machine to

the OFF position.

1. Connect the clip of jumper cable (R) to the

positive (+) battery terminal of the dead

machine.

2. Connect the other clip of jumper cable (R)

to the positive (+) battery terminal of the

booster vehicle.

3. Connect the clip of jumper cable (B) to the

negative (–) battery terminal of the booster

vehicle.

4. Connect the other clip of jumper cable (B)

to the engine block of the dead machine.

Connect the clip to a place as far from the

battery as possible.

Starting the engine

1. Check that the clips are securely

connected to the terminals.

2. Start the engine of the booster vehicle and

run it at high speed.

3. Start the engine of the dead machine.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды