Takeuchi TB210R Скачать руководство пользователя страница 78

Страница: 78 / 205

3-8

OPERATION

WARMING UP THE MACHINE

(HYDRAULIC OIL)

Operating the working equipment without

warming up the machine (hydraulic oil) is

dangerous, as the working equipment

cannot response to controls quickly or

may move in unexpected ways, and the

safety devices may not operate properly.

Be sure to sufficiently warm up the

machine.

IMPORTANT: Do not operate the levers

too quickly when the hydraulic oil

temperature is below 20°C (68°F). The

proper hydraulic oil temperature during

operation is 50 to 80°C (122 to 176°F). If

operations must be performed at lower

temperatures, heat up the hydraulic oil to

at least 20°C (68°F).

Normal warm-up

OPERATING THE MACHINE

1. Pull the throttle lever to the middle

position, then run the engine at medium

speed for about 5 minutes with no load.

2. Fully lower the safety lock lever to

disengage the lock and lift the bucket from

the ground.

3. Extend and retract each of the cylinders

slowly several times with no load.

4. Set the slew lock lever to the released

position before slewing.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды