Takeuchi TB210R Скачать руководство пользователя страница 191

Страница: 191 / 205

8-3

OPTIONS

CAUTIONS WHEN OPERATING

ATTACHMENTS

Long attachments reduce stability of the

machine. The machine may tip over if it

loses the balance when traveling or

slewing on slopes.

Never perform the operations listed below

as they are extremely dangerous.

GENERAL PRECAUTIONS

• Traveling down the slopes with the

attachment raised

• Traveling across slopes

• Slewing on slopes

• If there is a heavy attachment is

installed, the machine takes longer

distance than usual to come to a

complete stop when the stopping

operation is performed. Carefully judge

the distance so as not to bump into an

object around the machine. Keep a safe

distance from surrounding obstacles.

When a heavy attachment is installed,

natural drop (the gradual dropping of

the attachment under its own weight

when it is stopped in midair) increases.

• The machine can tip over more easily in

the lateral direction than in the

longitudinal direction.

· Do not slew sideways with a heavy

load at the how attachment. In

particular, do not slew sideways on

slopes.

· The attachment is heavier for

machines equipped with breakers or

crushers than for machines equipped

with the standard bucket. Do not

operate such machines sideways,

especially digging downhill.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды