Takeuchi TB210R Скачать руководство пользователя страница 157

Страница: 157 / 205

5-51

MAINTENANCE

Installation

1. Use the working equipment to lift the

body.

WHEN REQUIRED

2. Set the rubber crawler on the sprocket.

3. Set an iron pipe (1) in the rubber crawler

and turn the sprocket slowly in the reverse

direction.

4. Turn until the iron pipe (1) is directly next to

the idler and the rubber crawler lifts away

from the idler, then stop turning the

sprocket.

5. Slide the rubber crawler inward, engage it

on the idler, then pull out the iron pipe.

6. Check that the rubber crawler is securely

engaged on the sprocket and idler.

7. Tighten the rubber crawler to the standard

tension.

Refer to “Inspecting and adjusting the

crawler tension” on page 5-26.

8. Install the other rubber crawler using the

same procedure.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды