![background image](http://html2.mh-extra.com/html/takeuchi/tb210r/tb210r_operators-manual_3338445131.webp)
5-25
MAINTENANCE
AFTER THE INITIAL 50 HOURS (ONLY FOR NEW MACHINES)
REPLACING THE HYDRAULIC OIL
RETURN FILTER
• Stop the engine and allow the machine
to cool down before performing
maintenance.
· The engine and the hydraulic system
and many other parts of the machine
are hot immediately after the engine is
stopped. Touching these parts will
cause burns.
· The hydraulic oil is also hot and under
high pressure.
Be careful not to touch the hydraulic
oil when loosening the cap or plug.
Working on the machine under these
conditions could result in burns or
injuries due to the hot oil spurting out.
• Oil may spurt out if caps or filters are
removed or pipes are disconnected
before releasing the pressure in the
hydraulic system.
· Gradually loosen the vent plug to
relieve tank pressure.
· When removing plugs or screws, or
when disconnecting hoses, stand to
the side and loosen them slowly to
gradually release the internal pressure
before removing.
1. Open the engine hood.
2. Slowly loosen the air bleeding plug (2) to
relieve the internal pressure, and then
remove the plug.
3. Loosen the five bolts and remove the left
side cover (4).
4. Open the fuel lid.
5. Turn the filter (3) counterclockwise with the
filter wrench and remove it.
6. Clean the surface of installation of the filter
stand.
7. Apply a thin layer of oil on the packing of
the new filter.
8. Install the new filter.
· Tightening torque: 13.7 ± 2 N·m (10.1 ±
1.5 ft-lb.)
9. Install the left side cover (4).
10. Inspect the level with the sight gauge (1),
and replenish if the level is too low.
Refer to “Inspecting the hydraulic oil tank
level and replenishing” on page 5-19.
11. Pressurize the hydraulic oil tank.
(If not equipped with the air breather)
Refer to “Pressurizing the hydraulic oil
tank” on page 5-20.
Note:
For a machine equipped with the air
breather, no pressurization is necessary.
Содержание TB210R
