Takeuchi TB210R Скачать руководство пользователя страница 88

Страница: 88 / 205

3-18

OPERATION

OPERATING PROCEDURES

PROHIBITED OPERATIONS

• Do not operate on bedrock (hard or

soft).

• Do not slew/swing while traveling. If you

must operate the hoe attachment while

traveling, operate at speeds slow

enough so you have complete control at

all times.

Do not perform demolition or leveling

using slew force

OPERATING PROCEDURES

Do not demolish walls or level ground using

slew force. Also, do not dig the bucket teeth

into the ground during slewing. Doing so will

damage the hoe attachment.

Do not dig while traveling

Do not dig the bucket into the ground and

use the traveling force to dig.

Be gentle when using the hydraulic

cylinder

Do not extend the hydraulic cylinders to the

stroke ends. Operate them with leeway.

Do not support the machine body with the

hoe attachment when the body is lowering

with the arm cylinder fully extended. Doing

so concentrates the load on the arm cylinder

and could damage the arm cylinder.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды