Takeuchi TB210R Скачать руководство пользователя страница 130

Страница: 130 / 205

5-24

MAINTENANCE

INSPECTING AND ADJUSTING THE FAN

BELT

Stop the engine and allow the machine to

cool down before performing

maintenance.

• The engine, muffler, radiator, hydraulic

lines, sliding parts and many other parts

of the machine are hot immediately after

the engine is stopped. Touching these

parts will cause burns.

IMPORTANT: The loose belts could result

in bad battery charge, overheat of engine

or early wear of belt. Too tight belts could

damage the water pump or bearing and

belt used to drive the alternator.

IMPORTANT: Do not let any oil or grease

get on the belt.

Inspection

1. Open the maintenance cover.

AFTER THE INITIAL 50 HOURS (ONLY FOR NEW MACHINES)

2. Press at the center of the fan pulley (1)

and alternator pulley (2) to check the

tension (approx. 98 N or 22 lbf).

The slack (A) should be 7 to 9 mm (0.28 to

0.35 in).

3. Inspect the fan belt (3) and replace if it is

as follows.

· There are cuts or cracks.

· The belt is worn and touches the bottom

of the V groove in the pulley.

· The belt stretched too loose to be

adjusted.

1. Loosen the adjusting bolt (4) and the

locking bolt (5).

2. Move the alternator by using leverage to

adjust the slack.

3. Tighten the adjusting bolt (4) and the

locking bolt (5).

Note:

When replacing with a new belt, run

the engine at low idle speed for about 3 to 5

minutes to break in the new belt, before

adjusting the tension.

Adjustment

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды