Takeuchi TB210R Скачать руководство пользователя страница 168

Страница: 168 / 205

6-10

TROUBLESHOOTING

IF A WARNING LAMP LIGHTS UP

If a warning lamp lights up during operation, park the machine in a safe place and perform the

procedures described below.

IF A WARNING LAMP LIGHTS UP

Warning lamp

Lamp name

Causes and remedies

Battery charge

warning lamp

There is a problem with the fan belt or charger.

Inspect the fan belt for slack or breakage and adjust as

necessary.

If the lamp lights up even after maintenance, there is

likely a problem with the charger. Consult your sales or

service dealer for help.

Refer to “Inspecting and adjusting the fan belt” on page

5-24.

Engine oil

pressure

warning lamp

There is a problem in the engine lubrication system.

Check the engine oil level. If the lamp lights up when the

level is normal or even after replenishment of oil, consult

your sales or service dealer for help.

Refer to “Inspecting and replenishing the engine oil” on

page 5-17.

Coolant

temperature

warning lamp

The coolant temperature is too high and the engine is

overheating.

Refer to “If the engine overheats” on page 6-3.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды