Takeuchi TB210R Скачать руководство пользователя страница 17

Страница: 17 / 205

1-7

SAFETY

Using optional products

• Consult with Takeuchi before installing

optional attachments. Depending on the

type of attachments or the combination of

them, the attachment may come into

contact with the operator’s compartment

or the other parts of the machine. Make

sure that the optional attachment installed

is not contacted with other parts before

use.

• Do not use attachments that have not

been approved by Takeuchi. Doing so may

compromise safety or adversely affect the

machine’s operation or service life.

• Takeuchi will not be held responsible for

any injuries, accidents or damage to its

products caused by the use by a non-

approved attachment.

GENERAL PRECAUTIONS

Never modify the machine

Unauthorized modifications to this machine

can cause injury or death. Never make

unauthorized modifications to any part of this

machine.

If you modify or alter the configuration of the

machine in a way which results in a

restriction of the operator’s field of vision, a

new risk assessment will need to be

performed. If this becomes necessary,

contact your Takeuchi service or sales dealer.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды