Takeuchi TB210R Скачать руководство пользователя страница 193

Страница: 193 / 205

8-5

OPTIONS

SELECTING A LEVER PATTERN

The operating pattern of the left and right operating levers can be changed.

Before starting the engine, check the selector to see which operating pattern the left

and right operating levers are set.

SELECTING A LEVER PATTERN

SWITCHING THE LEVER PATTERN

(A) : ISO pattern

(G) : G pattern

1. Park the machine on a flat and rigid

ground, and stop the engine.

2. Open the engine hood.

3. Loosen the wing bolt (1).

4. Turn the selector valve lever (2) to switch

the pattern.

5. Tighten the wing bolt (1) and fasten the

lever (2) in place.

6. Close the engine hood.

7. Confirm the lever pattern.

Содержание TB210R














































































































































































































Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды

Takeuchi TB210R, Руководство оператора

Результаты поиска

Содержание TB210R

Отзывы:

Похожие инструкции для TB210R

Бренды по названию

Популярные бренды