manualshive.com logo in svg

Sun Microsystems Sun SPARC Enterprise M3000, Руководство пользователя


Поделиться
Скачать
background image

4-26

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

The meaning of each component status is as follows:

4.6.2

Clearing the Fault/Degradation Information

The information on a faulty or degraded component is cleared when the component
is replaced. For a component replacement, please contact a field engineer.

<Example 1>  The memory board and memory on the motherboard unit

(MBU) are degraded due to failure.

XSCF>

showstatus

    MBU_B Status:Normal;

*       MEMB#1 Status:Deconfigured;

*           MEM#3B Status:Deconfigured;

<Example 2>

The CPU is degraded due to the effect of the crossbar

unit (XBU) being degraded.

XSCF>

showstatus

    MBU_B Status:Normal;

*       CPUM#1-CHIP#1 Status:Deconfigured;

*   XBU_B#0 Status:Degraded;

<Example 3>  No degraded component is found.

XSCF>

showstatus

No failures found in System Initialization.

Faulted

The component is faulty and not operating.

Degraded

The component is operating. However, either an error has been
detected or the component is faulty. As a result, the component
might be operating with reduced functionality or performance.

Deconfigured

As a result of another component’s faulted or degraded status, the
component is not operating. (The component itself is not faulted or
degraded.)

Maintenance

The corresponding component is under maintenance. A

deletefru

(8),

replacefru

(8), and

addfru

(8) operation is

currently underway.

Normal

The component is operating normally.

Содержание Sun SPARC Enterprise M3000















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sun SPARC Enterprise M3000

IBM Enterprise Server S80 User Manual preview
Enterprise Server S80
Бренд: IBM Страницы: 282
Far south networks Com.X1 PBX Getting Started preview
Com.X1 PBX
Бренд: Far south networks Страницы: 4
IBM Power 570 Technical Overview And Introduction preview
Power 570
Бренд: IBM Страницы: 142
TYANO TS65A-B8036 Service Engineer'S Manual preview
TS65A-B8036
Бренд: TYANO Страницы: 102
Raritan Dominion SX II User Manual preview
Dominion SX II
Бренд: Raritan Страницы: 99
ZLAN ZLAN5443A User Manual preview
ZLAN5443A
Бренд: ZLAN Страницы: 13
IBM X 330 Series Installation Manual preview
X 330 Series
Бренд: IBM Страницы: 76
NEC N8100-2834F Maintenance Manual preview
N8100-2834F
Бренд: NEC Страницы: 138
Fujitsu PRIMERGY PG-RSBOP2 User Manual preview
PRIMERGY PG-RSBOP2
Бренд: Fujitsu Страницы: 68
Fujitsu SPARC Enterprise T5440 Server User Manual preview
SPARC Enterprise T5440 Server
Бренд: Fujitsu Страницы: 92
Fujitsu SPARC Enterprise T5140 Product Notes preview
SPARC Enterprise T5140
Бренд: Fujitsu Страницы: 138
Fujitsu SPARC Enterprise T5440 Server Service Manual preview
SPARC Enterprise T5440 Server
Бренд: Fujitsu Страницы: 214
Fujitsu SPARC Enterprise T5140 Installation Manual preview
SPARC Enterprise T5140
Бренд: Fujitsu Страницы: 130
Fujitsu SPARC M10-4 Service Manual preview
SPARC M10-4
Бренд: Fujitsu Страницы: 514
Grafenthal R2210 S2 User Manual preview
R2210 S2
Бренд: Grafenthal Страницы: 99
Aviosys IP Video 9100B User Manual preview
IP Video 9100B
Бренд: Aviosys Страницы: 30
San Telequip SC10E16A1 Series User Manual preview
SC10E16A1 Series
Бренд: San Telequip Страницы: 85
Axis 850 User Manual preview
850
Бренд: Axis Страницы: 69

Бренды по названию

Популярные бренды

Загрузить еще бренды