manualshive.com logo in svg

Sun Microsystems Sun SPARC Enterprise M3000, Руководство пользователя


Поделиться
Скачать
background image

B-6

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

■

Type of power event that occurred (Event). The following lists each event and its
meaning:

Factor by which the power event was instructed (Cause). The causes and their
meanings are as follows:

■

Domain ID for power event (DID)

■

Mode switch status on the operator panel (Switch). The following lists the
switches and their meanings:

Event

Meaning

SCF Reset:

The XSCF was reset.

Domain Power ON:

The domain power supply was turned on.

Domain Power OFF:

The domain power supply was turned off.

System Power ON:

The power supply of the server common section was turned on.

System Power OFF:

The power supply of the server common section was turned off.

XIR:

The XIR was reset.

Domain Reset:

The domain was reset.

Cause

Meaning

Self Reset:

Self-resetting of the XSCF reset the XSCF.

Power On:

Turning on the input power supply reset the XSCF.

System Reset:

The detection of an error reset the XSCF.

Panel:

Operating a switch on the operator panel caused a power event.

Scheduled:

Setting the TOD timer caused a power event.

RCI:

The I/O device connected to the RCI caused a power event.

AC Restored:

Power recovery turned on the power supply.

Operator:

An operator's instruction caused a power event.

Poweron Restart:

Retrying power on operation turned on the power supply.

Power Failure:

A power interruption cut off the power supply.

SW Request:

A Solaris OS instruction caused a power event.

Alarm:

The server environment or a hardware fault caused a power event.

Fatal:

Fatal caused a power event.

Panic:

Panic caused a power event.

Содержание Sun SPARC Enterprise M3000















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sun SPARC Enterprise M3000

Unisys ES5000 Manual preview
ES5000
Бренд: Unisys Страницы: 20
Xerox M Series Initial Setup Card preview
M Series
Бренд: Xerox Страницы: 2
IBM eServer BladeCenter HS40 Type 8839 Installation And User Manual preview
eServer BladeCenter HS40 Type 8839
Бренд: IBM Страницы: 120
IBM RS/6000 7043 260 Service Manual preview
RS/6000 7043 260
Бренд: IBM Страницы: 322
Ablecom CE-HE130S4 Series User Manual preview
CE-HE130S4 Series
Бренд: Ablecom Страницы: 43
QNAP TVS-72XU Series User Manual preview
TVS-72XU Series
Бренд: QNAP Страницы: 53
QCT QuantaGrid D51PH-1ULH Service Manual preview
QuantaGrid D51PH-1ULH
Бренд: QCT Страницы: 167
Ericsson HL950 Administrator'S Manual preview
HL950
Бренд: Ericsson Страницы: 159
IBM 8678 Installation And User Manual preview
8678
Бренд: IBM Страницы: 96
Motorola WPS870G - Wireless Print Server User Manual preview
WPS870G - Wireless Print Server
Бренд: Motorola Страницы: 115
Atrust t100 User Manual preview
t100
Бренд: Atrust Страницы: 21
ATON HDR44 Brochure & Specs preview
HDR44
Бренд: ATON Страницы: 2
Atop ABLELink SW2001 User Manual preview
ABLELink SW2001
Бренд: Atop Страницы: 51
Atop ABLELink GW21 MAXI Series Programming Manual preview
ABLELink GW21 MAXI Series
Бренд: Atop Страницы: 110
BITMAIN ANTMINER S19 Pro Installation Manual preview
ANTMINER S19 Pro
Бренд: BITMAIN Страницы: 17
Obvius A8812 Installation And Operation Manual preview
A8812
Бренд: Obvius Страницы: 39
Red Hat Linux Virtual Server Manual preview
Linux Virtual Server
Бренд: Red Hat Страницы: 82
R.V.R. Elettronica SpA TLC2000 User Manual preview
TLC2000
Бренд: R.V.R. Elettronica SpA Страницы: 128

Бренды по названию

Популярные бренды

Загрузить еще бренды