manualshive.com logo in svg

Sun Microsystems Sun SPARC Enterprise M3000, Руководство пользователя


Поделиться
Скачать
background image

2-108

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

Domain Configuration Procedure and Reference Sources

The steps from making domain configuration settings to activating a domain are
shown below. Each step contains a reference to where you can find additional
information.

In the M3000 server, Step 2 and Step 4 are not required. Perform Step 1, Step 3 and
Step 5, only if you change the domain configuration policy.

1. Log in to XSCF.

2. Make memory mirror mode and Uni/Quad-XSB settings for each PSB. (Note)

(See

showfru

(8),

setupfru

(8), and

Section 2.2.12, “System Board Configuration”

on page 2-122

.)

3. Create the DCL information corresponding to a domain, LSB, and XSB. (See

showdcl

(8),

setdcl

(8).)

4. Assign an XSB to the domain, according to the created DCL information. (See

addboard

(8),

showboard

(8). )

5. Turn on the power to the domain.

Note –

Make these settings only to change the number of XSB divisions and the

mirror mode.

Note –

For the procedure for installing, removing, or replacing a system board in

the server, see the

Service Manual

for your server. Also, for details on using the DR

function, see the

Dynamic Reconfiguration User’s Guide

.

Note –

For an overview of configuring domains, including an extensive example,

refer to the

Administration Guide

.

TABLE 2-24

lists setting items and the corresponding shell commands.

Содержание Sun SPARC Enterprise M3000















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sun SPARC Enterprise M3000

Ablecom CE-HE130S4 Series User Manual preview
CE-HE130S4 Series
Бренд: Ablecom Страницы: 43
IBM 1-Port USB Print Server Hardware User'S Manual preview
1-Port USB Print Server
Бренд: IBM Страницы: 15
Cisco Aironet 1500 Series Datasheet preview
Aironet 1500 Series
Бренд: Cisco Страницы: 8
Cisco 7835-H2 - Media Convergence Server Datasheet preview
7835-H2 - Media Convergence Server
Бренд: Cisco Страницы: 8
Cisco APP1000 - One Application Server Appliance Installation And Administration Manual preview
APP1000 - One Application Server Appliance
Бренд: Cisco Страницы: 20
Cisco APIC L3 Installation And Service Manual preview
APIC L3
Бренд: Cisco Страницы: 130
HP Compaq AlphaServer DS10 Overview preview
Compaq AlphaServer DS10
Бренд: HP Страницы: 43
HP Cluster Platform Hardware Kits v2010 Installation Manual preview
Cluster Platform Hardware Kits v2010
Бренд: HP Страницы: 12
HP CB900s i4 Disassembly Instructions Manual preview
CB900s i4
Бренд: HP Страницы: 12
HP hpe proliant dl20 gen9 User Manual preview
hpe proliant dl20 gen9
Бренд: HP Страницы: 131
HP Cisco MDS 8/12c Release Note preview
Cisco MDS 8/12c
Бренд: HP Страницы: 44
HP Cluster Platform Installation Manual preview
Cluster Platform
Бренд: HP Страницы: 74
HP Cisco MDS 8/24c Release Note preview
Cisco MDS 8/24c
Бренд: HP Страницы: 44
HP Cluster Platform Introduction Manual preview
Cluster Platform
Бренд: HP Страницы: 88
HP HPE ProLiant DL180 Gen10 Maintenance And Service Manual preview
HPE ProLiant DL180 Gen10
Бренд: HP Страницы: 157
HP HPE ProLiant DX360 Gen10 User Manual preview
HPE ProLiant DX360 Gen10
Бренд: HP Страницы: 187
HP Apollo 2000 System Maintenance And Service Manual preview
Apollo 2000 System
Бренд: HP Страницы: 178
HP Color LaserJet Enterprise CP5525 Configuration preview
Color LaserJet Enterprise CP5525
Бренд: HP Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды