manualshive.com logo in svg

Sun Microsystems Sun SPARC Enterprise M3000, Руководство пользователя


Поделиться
Скачать
background image

Chapter 8

Upgrade of XSCF Firmware and Maintenance

8-15

Note –

The display might be different according to XCP version and system

configuration.

At this time, the XSCF will reset and the XSCF session will disconnect, so
please connect the XSCF again. Only the application of the XSCF firmware is
completed.

Note –

The work described below applies to a system with redundant XSCF Units.

i) Perform the firmware update in order, beginning with the standby side and then
the active side automatically. After the update on the standby side is completed, the
active and standby sides are switched. At this time, the XSCF reset is done and the
XSCF session is disconnected.

ii) Re-connect the XSCF and log in again.

iii) XSCF firmware update is completed.

iv) When the firmware update completes, the active and the standby states of the
XSCF unit have become the opposite of original state. For instance, if the firmware
update is executed on XSCFU#0, when completing the command, XSCFU#1 would
become the active side. To switch the XSCF, execute the

switchscf

(8) command.

To confirm the switching between XSCFs, execute the

showhardconf

(8) command.

<Example>
XSCF> switchscf -t Standby
The XSCF unit switch between the Active and Standby states. Continue? [y|n] :y

d. To confirm that the XSCF firmware update has finished, use the

showlogs

(8)

command with the monitor option. Confirm no abnormality is found during
the update. If the "XCP update has been completed" message is displayed in
each XSCF Unit, the firmware update has completed.

4. To complete the update of the OpenBoot PROM firmware, restart the domain.

5. Confirm that the version of the system firmware that is running is that of the

firmware applied at the XSCF Shell command line by using the

version(8)

command.

XSCF>

showlogs monitor

:

Jun 20 07:25:48 FF1-1-0 monitor_msg: SCF:XCP update has been completed (XCP

version=1082)

Содержание Sun SPARC Enterprise M3000















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sun SPARC Enterprise M3000

Eaton RS Enclosure Unpacking Manual preview
RS Enclosure
Бренд: Eaton Страницы: 2
IntesisBox Modbus Server-Cerberus ISO1745 Installation Manual preview
Modbus Server-Cerberus ISO1745
Бренд: IntesisBox Страницы: 5
Supermicro SUPERSERVER 5018D-FN8T User Manual preview
SUPERSERVER 5018D-FN8T
Бренд: Supermicro Страницы: 124
QNAP TVS-72XU Series User Manual preview
TVS-72XU Series
Бренд: QNAP Страницы: 53
QCT QuantaGrid D51PH-1ULH Service Manual preview
QuantaGrid D51PH-1ULH
Бренд: QCT Страницы: 167
Crestron CEN-RVS-R210 Quick Start Manual preview
CEN-RVS-R210
Бренд: Crestron Страницы: 2
Lenovo 7Y45 Setup Manual preview
7Y45
Бренд: Lenovo Страницы: 116
Lenovo 70F0 User Manual And Hardware Maintenance Manual preview
70F0
Бренд: Lenovo Страницы: 96
Lenovo 8753 Product Manual preview
8753
Бренд: Lenovo Страницы: 46
Lenovo 7Y54 Maintenance Manual preview
7Y54
Бренд: Lenovo Страницы: 138
Lenovo 8871 Product Manual preview
8871
Бренд: Lenovo Страницы: 56
Lenovo 8869 Product Manual preview
8869
Бренд: Lenovo Страницы: 64
Lenovo DU User Manual preview
DU
Бренд: Lenovo Страницы: 226
Lenovo BladeCenter HS22 Installation And User Manual preview
BladeCenter HS22
Бренд: Lenovo Страницы: 96
Lenovo BladeCenter HS23 Installation And User Manual preview
BladeCenter HS23
Бренд: Lenovo Страницы: 104
Lenovo 643815U Installation Manual preview
643815U
Бренд: Lenovo Страницы: 90
Lenovo 6435 User Manual preview
6435
Бренд: Lenovo Страницы: 76
Lenovo 7Z70 Reference preview
7Z70
Бренд: Lenovo Страницы: 212

Бренды по названию

Популярные бренды

Загрузить еще бренды