manualshive.com logo in svg

Sun Microsystems StorEdge T3+, Руководство по обслуживанию


Поделиться
Скачать
background image

Chapter 5

Disks and Drives

5-13

5.4

Upgrading Disk Drive Firmware

The latest disk drive firmware versions are located on the SunSolve web site:

http://sunsolve.sun.com

During a disk drive firmware download, the functionality of the array is limited. To
avoid system problems, verify that:

■

A current backup copy of array data exists.

■

The data path to the host has been quiesced. There must not be any
I/O activity during the disk drive firmware download.

■

The Ethernet connection is not being used for any other operation during this
procedure. If Component Manager is being used to monitor the array, disable the
automatic polling utility. Refer to the current Sun StorEdge Component Manager
Users Guide for instructions to disable polling.

Caution –

If a host-mounted utility program such as Component Manger is actively

polling, problems might occur during the firmware download. Disable the polling
utility within Component Manager during this procedure to avoid problems.

■

No unnecessary command line program interaction with the array is performed
during the disk drive firmware download.

Note –

The disk firmware download takes approximately 20 minutes for 9 drives.

Do not attempt to interrupt the download or perform other command-line functions
during the process. The command prompt reappears after the download process has
completed.

To upgrade the firmware:

1. Use

ftp

to transfer the firmware to the array

root

directory in binary mode.

See Section 2.3, “Establishing an FTP Session” on page 2-5 for additional
information.

Note –

The file name of files being transferred to the local disk must be 12

characters or less in size and start with an alphabetic character (not numeric).

2. Establish a Telnet connection to the array.

See Section 2.2, “Establishing a Telnet Session” on page 2-3.

Содержание StorEdge T3+

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorEdge T3+

d&b audiotechnik J Series Rigging Manual preview
J Series
Бренд: d&b audiotechnik Страницы: 34
Federal Signal Corporation E1 Installation And Maintenance Instructions Manual preview
E1
Бренд: Federal Signal Corporation Страницы: 12
Federal Signal Corporation E1 Nstallation And Service Instructions preview
E1
Бренд: Federal Signal Corporation Страницы: 8
KAM SF Series Instruction Manual preview
SF Series
Бренд: KAM Страницы: 4
808audio SPKA10 Instructions preview
SPKA10
Бренд: 808audio Страницы: 2
Laskomex CD-2000 Installation, Operation & Programming Instructions preview
CD-2000
Бренд: Laskomex Страницы: 36
XD XCLUSIVE Nevada Instruction Manual preview
Nevada
Бренд: XD XCLUSIVE Страницы: 20
WaterLogic WL900 Service Manual preview
WL900
Бренд: WaterLogic Страницы: 29
WATERKOTTE EcoTouch Ai1 Geo Planning And Installation preview
EcoTouch Ai1 Geo
Бренд: WATERKOTTE Страницы: 60
RCF ACUSTICA H series User Manual preview
ACUSTICA H series
Бренд: RCF Страницы: 10
Renkforce PA102 Operating Instructions preview
PA102
Бренд: Renkforce Страницы: 4
Power Dynamics 100.093 Instruction Manual preview
100.093
Бренд: Power Dynamics Страницы: 16
Truweld Equipment TWE - SC2402 Operation Manual preview
TWE - SC2402
Бренд: Truweld Equipment Страницы: 28
EXTOL VORTEX PRECEDENCE G1 User Manual preview
VORTEX PRECEDENCE G1
Бренд: EXTOL Страницы: 104
HTP InverArc 160 Plus Owner'S Manual preview
InverArc 160 Plus
Бренд: HTP Страницы: 10
QMotion QM 1000A User Manual preview
QM 1000A
Бренд: QMotion Страницы: 16
YA WOODSTOCK Quick Start Manual preview
WOODSTOCK
Бренд: YA Страницы: 2
Opus OP-6505B User Manual preview
OP-6505B
Бренд: Opus Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды