manualshive.com logo in svg

Sun Microsystems StorEdge T3+, Руководство по обслуживанию


Поделиться
Скачать
background image

Chapter 4

Controller Card Assembly

4-5

6. Pull the controller card out using the latch handles.

7. Insert the new controller card.

8. Lock the new controller card by pushing in the latch handles.

Use a coin or small screwdriver to press in and secure the latch handle.

9. Insert the fiber-optic cable and MIA back into the FC-AL connector.

10. Insert the Ethernet cable into the 10BASE-T connector.

11. Check the controller status LED to determine when the controller is operational.

While the controller boots, the controller status LED is solid amber. When the
controller is operational, the LED is green.

12. Verify the status of the controller card using either the CLI or Component

Manager.

Refer to Section 3.7.3, “Checking FRU Status” on page 3-18, or the Sun StorEdge
Component Manager User’s Guide for instructions.

Note –

In a partner group configuration, the controller fails over to the alternate

master when there is a controller card failure in a master unit. After the controller
board is replaced, the partner group performs a reset command to return to the
original failover configuration of master and alternate master.

4.3

Upgrading Controller Firmware

The controller firmware can be upgraded on an operational system. However, for the
upgrade to take effect, the controller must be reset (booted). While the controller
boots, the array is not available for storage.

The firmware upgrade procedures that follow must be done through the Ethernet
connection. The latest firmware version is located on the SunSolve web site:

http://sunsolve.sun.com

The following conditions apply to firmware upgrades:

■

The firmware has to be resident on the host for this operation.

■

The Sun StorEdge T3 and T3+ array has to have a supervisor password prior to
attempting this procedure.

Содержание StorEdge T3+

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorEdge T3+

ABB L240 Series Product Manual preview
L240 Series
Бренд: ABB Страницы: 20
Oklahoma Sound 901 Product Handbook preview
901
Бренд: Oklahoma Sound Страницы: 4
B&W electronics 802 Instruction Manual preview
802
Бренд: B&W electronics Страницы: 13
Olympia 5912 Operating Manual preview
5912
Бренд: Olympia Страницы: 5
Xilica Audio Design XP Series Quick Start Manual preview
XP Series
Бренд: Xilica Audio Design Страницы: 10
Oakley Sound Modular Series Builder'S Manual preview
Modular Series
Бренд: Oakley Sound Страницы: 15
Oasis Modular Series User Manual preview
Modular Series
Бренд: Oasis Страницы: 18
Valcom VIP-431A-DS-IC Assembly preview
VIP-431A-DS-IC
Бренд: Valcom Страницы: 3
Harman JBL CINEMA SB130 Quick Start Manual preview
JBL CINEMA SB130
Бренд: Harman Страницы: 16
Electro-Voice SH-1810L-ER Service Data preview
SH-1810L-ER
Бренд: Electro-Voice Страницы: 4
Dynacord LITTLEMAX 2 Specifications preview
LITTLEMAX 2
Бренд: Dynacord Страницы: 2
Novetec NGL-LJM-4 User Manual preview
NGL-LJM-4
Бренд: Novetec Страницы: 7
Furrion DV3150 Instruction Manual preview
DV3150
Бренд: Furrion Страницы: 21
Harman REVEL PERFORMA Be4 F226Be Owner'S Manual preview
REVEL PERFORMA Be4 F226Be
Бренд: Harman Страницы: 10
Telwin SUPERIOR TIG 242 Instruction Manual preview
SUPERIOR TIG 242
Бренд: Telwin Страницы: 108
EAW MK5166 Dimensions preview
MK5166
Бренд: EAW Страницы: 1
Vonyx 178.870 Instruction Manual preview
178.870
Бренд: Vonyx Страницы: 16
LATICRETE STRATA_HEAT 120V Quick Start Manual preview
STRATA_HEAT 120V
Бренд: LATICRETE Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды