manualshive.com logo in svg

Sun Microsystems StorEdge T3+, Руководство по обслуживанию


Поделиться
Скачать
background image

iv

Sun StorEdge T3 and T3+ Array Field Service Manual • September 2001

FCC Class B Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

Note:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

■

Reorient or relocate the receiving antenna.

■

Increase the separation between the equipment and receiver.

■

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

■

Consult the dealer or an experienced radio/television technician for help.

Shielded Cables:

Connections between the workstation and peripherals must be made

using shielded cables in order to maintain compliance with FCC radio frequency emission
limits. Networking connections can be made using unshielded twisted pair (UTP) cables.

Modifications:

Any modifications made to this device that are not approved by Sun

Microsystems, Inc. may void the authority granted to the user by the FCC to operate this
equipment.

ICES-003 Class A Notice - Avis NMB-003, Classe A

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

ICES-003 Class B Notice - Avis NMB-003, Classe B

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Содержание StorEdge T3+

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorEdge T3+

Yamaha DHR Series Owner'S Manual preview
DHR Series
Бренд: Yamaha Страницы: 24
jacarta SP8 Test Manual preview
SP8
Бренд: jacarta Страницы: 4
NAPCO MAGNUM ALERT-725 Manual preview
MAGNUM ALERT-725
Бренд: NAPCO Страницы: 8
NAPCO MAGNUM ALERT 854 SYSTEM Manual preview
MAGNUM ALERT 854 SYSTEM
Бренд: NAPCO Страницы: 14
NAPCO MA3000 Installation Instructions preview
MA3000
Бренд: NAPCO Страницы: 4
NAPCO FREEDOM - Manual preview
FREEDOM -
Бренд: NAPCO Страницы: 28
NAPCO XP-400 Using Instructions preview
XP-400
Бренд: NAPCO Страницы: 16
Zeck Audio VECTOR S3A Owner'S Manual preview
VECTOR S3A
Бренд: Zeck Audio Страницы: 16
Paradox ESPRIT 728 ULT Reference & Installation Manual preview
ESPRIT 728 ULT
Бренд: Paradox Страницы: 56
Transmitter Solutions iCE--Entry--R Installation Manual preview
iCE--Entry--R
Бренд: Transmitter Solutions Страницы: 50
Youly Electric YL Powership MMA-250FI Operator'S Manual preview
YL Powership MMA-250FI
Бренд: Youly Electric Страницы: 16
GSD Wi-Corporate Controller Installation & User Manual preview
Wi-Corporate Controller
Бренд: GSD Страницы: 14
EAW Cinema MC4972 Technical Specifications preview
Cinema MC4972
Бренд: EAW Страницы: 2
QOLSYS IQ PANEL 2 PLUS Quick Manual preview
IQ PANEL 2 PLUS
Бренд: QOLSYS Страницы: 2
NAPCO MVA-1000 Instruction Manual preview
MVA-1000
Бренд: NAPCO Страницы: 4
Thodio ibox Owner'S Manual preview
ibox
Бренд: Thodio Страницы: 6
Samson dB300a Owner'S Manual preview
dB300a
Бренд: Samson Страницы: 72
Party Light & Sound PARTY-BOX212 Instruction Manual preview
PARTY-BOX212
Бренд: Party Light & Sound Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды