Stihl MS 231 Скачать руководство пользователя страница 82

Страница: 82 / 114

MS 231, MS 231 C, MS 251, MS 251 C

12.

Fuel System

12.1

Air Filter

Dirty air filters reduce engine power,
increase fuel consumption and
make starting more difficult. The air
filter should be checked when there
is a noticeable loss of engine power.

– See also Troubleshooting,

3.6,

3.7

– Remove the shroud,

6.4

Rotate the air filter (1)
counterclockwise and lift it away.

– Check the air filter and clean or

replace if necessary
– see instruction manual.

– Reassemble in the reverse

sequence.

2310RA312 TG

12.2

Baffle

– Remove the air filter,

12.1

Unscrew the nuts (arrows).

Remove the baffle (1).

– Check the baffle and replace it if

necessary

– Reassemble in the reverse

sequence.

12.3

Filter Base

– Remove the air filter,

12.1

– Remove the choke rod,

10.3.3

– Remove the baffle,

12.2

Pry the filter base (1) out of the
buffer (2).

2310RA313 TG

2310RA195 TG

Pull the filter base (1) off the
studs (arrows).

Pull the filter base (1) out of the
buffer (2).

Pull the short circuit wire (1) and
ground wire (2) out of the
guides (arrows).

– Remove the contact spring,

7.7.4

– Remove the switch shaft,

10.1

– Remove the filter base.

2310RA198 TG

2310RA197 TG

2310RA196 TG

All manuals and user guides at all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды