Stihl MS 231 Скачать руководство пользователя страница 32

Страница: 32 / 114

MS 231, MS 231 C, MS 251, MS 251 C

5.6

Bar Mounting Stud

– Remove the chain sprocket

cover.

Push stud puller
5910 893 0501 (1) over the collar
stud (2) as far as it will go and
unscrew the stud counter-
clockwise.

– Coat the collar stud with

threadlocking adhesive, fit and
tighten down firmly,

– Reassemble all other parts in the

reverse sequence.

2310RA046 TG

Repair solution

If the thread in the engine housing is
badly damaged or stripped it will not
be possible to tighten the standard
collar stud to the specified torque –
the security of the collar stud is no
longer guaranteed.

In such a case use the collar stud in
the screw list as a repair solution,

2.5.

– Remove the standard collar stud

– do not re-drill the hole.

Coat the thread of the collar
stud (1) with threadlocking
adhesive,

– Fit the collar stud by hand so that

it engages the existing thread.

– Screw home the collar stud and

tighten it down firmly.

– Reassemble all other parts in the

reverse sequence.

2310RA047 TG

All manuals and user guides at all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды