Stihl MS 231 Скачать руководство пользователя страница 23

Страница: 23 / 114

MS 231, MS 231 C, MS 251, MS 251 C

Remove the retaining ring (1).

Pull the hand guard (1) and brake
lever (2) off the pivot
pins (arrows) together.

– Remove the hand guard and

brake lever.

Remove the spacer washer (1)
and strap (2).

Pull out the flat spring (3).

2310RA016 TG

2310RA017 TG

2310RA018 TG

Take the brake lever (2) out of
the hand guard (1).

– Check the anchor pin – if it is

worn, install a new engine
housing.

– Check the cam on the hand

guard and replace the hand
guard if necessary.

Installing

– Clean the pivot pins and

disassembled parts,

– Lubricate the pivot pins,

Push the loop of the flat spring (1)
into its seat (arrow) as far as
stop.

2310RA019 TG

TOP

2310RA020 TG

Fit the strap (1) on the pivot
pins (2) and (3) so that "TOP"
faces outwards and the
curve (arrow) faces up.

Slip the spacer washer (1) onto
the pin (2).

Hold the brake lever (2) so that
the brake spring attachment
point (arrow) is at the top.

Push the brake lever (2) into the
recess in the hand guard (1) and
line up the holes.

TOP

2310RA021 TG

2310RA022 TG

2310RA023 TG

All manuals and user guides at all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды