Stihl MS 231 Скачать руководство пользователя страница 84

Страница: 84 / 114

MS 231, MS 231 C, MS 251, MS 251 C

12.4

Air Guide Shroud

– Remove the fan housing,

8.2

– Pull the filter base off the studs

and put it to one side with the
wiring harness still attached,

12.3

– Remove the carburetor,

12.5

– Remove the throttle rod,

10.3.4

– Remove the carburetor carrier,

12.8

– Pull the boot off the spark plug.

Pull the rubber grommet (1) and
wiring harness out of the
guides (arrows).

– Put the wiring harness with filter

base to one side.

Take out the screws (1).

2310RA319 TG

2310RA320 TG

Push the grommet (arrow) of the
fuel hose (1) downwards and out.

Ease the air guide shroud (1)
over the stop (arrow) and lift it a
little.

Push the manifold flange (1) out
of the air guide shroud (2) in the
direction of the cylinder and pull
the air guide shroud away at the
same time.

– Pull the fuel hose out of the air

guide shroud.

– Remove the air guide shroud.

2310RA321 TG

2310RA322 TG

2310RA323 TG

– Pull out the shutter , check it and

replace if necessary.

Installing

Push the shutter (1) into the
guide until it snaps into place.

To fit the manifold (2) through the
air guide shroud's opening, wind
a piece of string (1) (about 15 cm
long) around the back of manifold
flange.

– Coat manifold flange with STIHL

press fluid to simplify installation,

2310RA324 TG

2310RA325 TG

All manuals and user guides at all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды