Stihl MS 231 Скачать руководство пользователя страница 71

Страница: 71 / 114

MS 231, MS 231 C, MS 251, MS 251 C

– Take out the screws (1).

Ease the handlebar (2) sideways
and take it out of the guide
(arrow).

Remove the screws (1) from the
underside of the machine and lift
the handlebar (2) out of its
seat (arrow).

Push the handlebar (1) out of the
lower guide.

– Remove the handlebar (1), check

it and replace if necessary.

2310RA156 TG

2310RA157 TG

0001RA232 TG

– Inspect the AV spring and

replace if necessary,

9.3

Installing

– Place the handlebar in position.

Lift the handlebar (1), lug (2) first,
into the recess (arrow) until it
locates in the tank housing seat.

– Insert the screws and tighten

them down firmly.

Ease the handlebar (1) sideways
and place it in the guide (arrow).

– Insert the screws and tighten

them down firmly.

2310RA158 TG

2310RA159 TG

Place plug (1) of AV spring on the
cylinder.

Insert and tighten down the
screw (2) firmly.

– Reassemble all other parts in the

reverse sequence.

2310RA246 TG

All manuals and user guides at all-guides.com

all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды