Stihl MS 231 Скачать руководство пользователя страница 86

Страница: 86 / 114

MS 231, MS 231 C, MS 251, MS 251 C

12.4.1 Air Guide Shroud –

Models with Manual Fuel
Pump

– Remove the fan housing,

8.2

– Pull the filter base off the studs

and put it to one side with the
wiring harness still attached,

12.3

– Remove the carburetor,

12.5

– Pull the boot off the spark plug.

Pull the wiring harness and
rubber grommet (1) out of the
guides (arrows).

– Put the wiring harness with filter

base to one side.

– Remove the throttle rod,

10.3.4

– Remove the carburetor carrier,

12.8

2310RA332 TG

Take out the screw (1).

Remove the connector (2) and
disconnect it from the fuel return
hose (3).

Pull the fuel return hose (1) out of
the guides (arrows).

Take out the screws (1).

2310RA333 TG

2310RA334 TG

2310RA335 TG

Push the grommet (arrow) of the
fuel hose (1) downwards and out.

Ease the air guide shroud (1)
over the stop (arrow) and lift it a
little.

Push the manifold flange (1) out
of the air guide shroud (2) in the
direction of the cylinder and pull
the air guide shroud away at the
same time.

2310RA336 TG

2310RA337 TG

2310RA338 TG

All manuals and user guides at all-guides.com

all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды