Stihl MS 231 Скачать руководство пользователя страница 33

Страница: 33 / 114

MS 231, MS 231 C, MS 251, MS 251 C

Engine

6.1

Muffler

Always check and, if necessary,
repair the fuel system, carburetor,
air filter and ignition system before
looking for faults on the engine.

– Troubleshooting,

3.7

– Remove the shroud,

6.4

Before removing the muffler, set the
piston to top dead center to ensure
that no dirt falls into the cylinder.

Pry out the plugs (1)
– do not re-use plugs that have
been removed.

Take out the screws (1).

Remove the muffler (2), check
and replace if necessary.

– Remove the exhaust gasket

– always install a new exhaust
gasket.

2310RA067 TG

2310RA068 TG

– Remove and install the spark

arresting screen, if fitted – see
instruction manual.

Installing

– Cover the exhaust port. Remove

any dirt from around the cylinder
and exhaust port.

Check and clean the sealing
faces (arrows), remove any
gasket residue – make sure there
is no gasket residue or dirt in the
exhaust port.

Always replace components with
damaged sealing faces.

– Position the new exhaust

gasket (1) so that the
tabs (arrows) point towards the
cylinder.

Fit the new exhaust gasket (1)
and use the tabs (arrows) to line
it up on the cylinder.

2310RA069 TG

2310RA070 TG

Carefully place the muffler (1) in
position.

Check the position of the gasket
and fit the screws (2).

Insert and tighten down the
screws (2) firmly.

– Use a blunt tool to push home the

new plugs squarely and uniformly
– take care not to damage the
plugs.

2310RA071 TG

All manuals and user guides at all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды