Stihl MS 231 Скачать руководство пользователя страница 22

Страница: 22 / 114

MS 231, MS 231 C, MS 251, MS 251 C

Installing

– Disengage the chain brake

Hold the brake band (1)
sideways, attach it to the brake
lever (2) and then swing it in the
direction of its seat.

Position the brake band (1) in the
guide (arrow).

– Engage the chain brake.

Push the brake band (1) over the
guide lugs (arrows) and into its
seat.

2310RA009 TG

TOP

2310RA010 TG

TOP

2310RA011 TG

Push the brake band (1) into
its seat (arrow) as far as stop.

Fit the screw (2) on the underside
of the machine and tighten it
down firmly.

Engage the cover (1) in
the slots (arrows) first.

Place the cover (1) in position.

Insert and tighten down the
screws (2) firmly.

2310RA012 TG

2310RA013 TG

TOP

2310RA014 TG

– Install the clutch drum,

4.1

The clutch drum must rotate freely
when the chain brake is
disengaged.

– Carry out the other checks,

5.1

– Reassemble all other parts in the

reverse sequence.

5.3

Brake Lever

– Troubleshooting,

3.2

– Remove the shroud,

6.4

– Remove the fan housing,

8.2

– Remove the brake band,

5.2

– Engage the chain brake.

The brake spring is now relaxed.

Use the assembly tool
1117 890 0900 to disconnect the
brake spring (1) from the anchor
pin (arrow).

– Remove the brake spring from

the brake lever.

TOP

2310RA015 TG

All manuals and user guides at all-guides.com

Содержание MS 231



















































































































Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды

Stihl MS 231, Руководство пользователя

Результаты поиска

Содержание MS 231

Отзывы:

Похожие инструкции для MS 231

Бренды по названию

Популярные бренды