255MM SLIDING COMPOUND MITRE SAW
MODEL NO:
SMS255.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
TANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH
HE
P
PR
O
ODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE
ER
S
SON
NAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
if the multi-tool is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance
Test)
tested.
Electrical safety information. It is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. IMPORTANT
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is
fi
tted with the
correct fuse - see fuse rating in these instructions.
DO
NOT
abuse the power cord.
NEVER
use the cord for carrying, or pulling the saw. Keep cord away from heat, oil, sharp edges or
moving
parts.
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a
fi
rm grip on the plug.
DO
NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
quali
fi
ed electrician.
1.1.4.
This product is
fi
tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch o
ff
the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a quali
fi
ed electrician.
Class II products are wired with live (brown) and neutral (blue) only and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO
NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a quali
fi
ed electrician.
If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and
should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may
be used in the other output sockets, we recommend the use of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it
is marked for outdoor use.
1.2. GENERAL
SAFETY
Familiarise yourself with the applications, limitations and potential hazards of the saw.
DO NOT
let familiarity gained from frequent use of the saw allow you to become complacent and ignore tool safety principles.
▲
DANGER!
Prevent unintentional starting. Ensure the switch is in the OFF position before connecting to the power source, picking up or
carrying the saw.
Stay alert, watch what you are doing and use common sense when operating the saw.
WARNING!
Disconnect the saw from the mains power before changing accessories, servicing or performing any maintenance.
The machine must only be serviced by a qualified person or service agent. Contact your Sealey stockist for information.
Select a work area suitable for the saw and keep the area clean, tidy and free from unrelated materials. Ensure that there is adequate
lighting.
Wood dust can be harmful to health by inhalation and skin contact. Concentrations of small dust particles in the air can form an
explosive mixture. Ensure that there is adequate ventilation and that the saw is attached to a dust-extraction unit.
Maintain the saw in good condition, check moving parts alignment regularly. Keep saw blades clean and sharp.
,
Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING!
Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
A guard, or any other part, that is damaged should be repaired or replaced before the saw is next used. The safety guard is a
mandatory fitting where the saw is used in premises covered by the Health & Safety at Work Act.
Before commencing work, ensure the saw blade is set to cut in the correct direction, securely fastened, sharp and is compatible with the
SMS255.V3 Issue 1 21/05/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear a mask
RECOMMENDED FUSE
RATING: 13A
Warning!
Laser beam
